Sp-110 Bike

3° Road Bike Cleat Black

The SP-110 cleats is a lightweight and compatible with LOOK Keo spring structure pedal

• 15% glass fiber composite.
• Non-slip rubber attached to the surface of the cleat.
• The shortened screws are more suitable for carbon fiber cycling shoes.
• High-quality production molds ensure the quality stability of industrial production.

Install tick marks

Install the scale line to help you quickly replace the cleats.

The anti-slip grip can prevent the rider from falling when temporarily getting off the bike and walking.

Better cilp in and lighter weight

15% glass fiber is added to the cleats. The overall hardness of the cleats is greatly improved. It makes the foot feel more crisp when the cleats are clip in the pedal.

Optimized screws

The light and thin cycling shoes aiming at the carbon fiber sole. We redesigned the length of the screw. The new screw prevents the screw from screwing through the sole.

Technical SpecificationsMaterial85%PC(Polycarbonate);15%GF(Glass fiber)Angular freedom3°ColorBlackUseHEPINGJIANGENBO Road Bike Pedal，compatible with Look Keo's spring-loaded pedalsWeight pair + fastenings77gAccessories6 SCREWS AND 6 WASHERS

The Difference Between 3 ° Cleat And 0 ° Cleat3 Threaded Holes To Install The Cleat 
The cleat suitable for three-hole cycling shoes.

 Technical Specifications Material 85%PC(Polycarbonate);15%GF(Glass fiber) Angular freedom 0° Color Grey Use HEPINGJIANGENBO Road Bike Pedal，compatible with Look Keo's spring-loaded pedals Weight pair + fastenings 77g Accessories 6 SCREWS AND 6 WASHERS 
PRESENTATION AND ASSEMBLY OF THE CLEATS  

BOTTOM VIEW

1:Adjustment:the 3 dajustment opening allow fitting the cleat under the shoe sole.These are rectangular and can be adjusted horizontally and longitudinally so that the sole can be accurately positioned.

2:Plates(6)

3:Cleat fastening screws(6):they shall be tightened using 4mm Allen wrench.

4:Anti-skid pads: These polyurethane pads control the risk of slipping while walking. Note: When any one of the anti-skid pads is seriously worn, it is recommended to replace the new lock piece to achieve the best use effect.

SIDE VIEW:

1. Bending radius: There is a bending radius on the back of the cleat,providing shoe sole the required camber which is essential to make shoes comfortable.The soles of shoes used with these cleats shall also have the same bending radius.otherwise the cleat might get out of shape after it is fixed and provide inadequate foot support.

2.Axle-pedal mark:this reference mark indicates pedal axle positon when the cleat is inserted in the pedal.

Cleat Installation:Caution:make sure that the cleats are suitably tightened under your shoes before snapping.After replacing the cleats and before using the bike,always make sure that pedal spring tension is adequate.If release is too easy or too difficult,this might result in fall and serious injury.Fasten the cleat to shoe bottom using screws and plates provided with the cleats.

Cleat Adjustment:

Step1:Cleat side adjustment:Center the cleat as much as possible under the shoe(sole fixing holes are located in the centre cleat openings).

Step2:Cleat adjustment lengthwise(at front/backend of shoes bottom).Most experts consider adjustment to be optimal when the reference mark on the cleat(indicating pedal axle)is located under the axis of inside metatarsus articulation.The axis of your inside metatasus articulation is located in the centre section of foot-big toe articulation.

Step3:Once the cleat is adjusted as stated above,fasten it to the shoe using the fixing screws.Tightening is done using 4mm Allen wrench.The tightening torque shall be set within 5.5~6 Nm range.

Step4:Engage your foot in the pedal and run a few meters with your bicycle. If your shoes collide with the bike, or your ankles and knees are unable to exert force or are overburdened, please adjust the direction of the locking tabs. Repeat this operation until you feel completely comfortable while riding.

ENGAGEMENT/RELEASE  Engagement:Insert the cleat in the pedal in accordance with trajectory 1 and press down on the pedal as per trajectory 2 to lock the cleat.

Release:Rotate your heel towards the outside 3 and it will disengage.

WARNING!:Don't release towards the inside,as this may case the heel to touch the spokes and case a crash.